Siglent SPS5000X Series Wide range programmable Switching DC Power Supply

Channel Output
One Channel
50 V/10 A/180 W

Display
2.4-inch OLED Screen

Resolution
1 mV/1 mA
 

---

Product Introduction
SIGLENT SPS5000X Programmable Switching DC Power Supplies provide a wide range of output power using single-channel and multi-channel output configurations coupled with constant power capability. The SPS5000X series of power supplies includes sixteen models with voltages to 160 VDC and power to 1080 W. SPS5000X power supplies can be connected in series (2 units) or in parallel (3 units) to meet the requirements of 0~320V and 0~270A, with a maximum combined power of 3240W.

Key Features

• Rated Output Voltage：40 V / 50 V / 80 V / 160 V
• Rated Output Power：180 W / 360 W / 720 W / 1080 W
• Wide range of output voltage and current, high efficiency power supply
• CV, CC priority mode selection, better protection of equipment under test
• Configurable three-channel timing output
• 170° wide viewing angle OLED screen, remote web control

 

---

Product Advantage

Multi-combination output
The SPS5000X series includes a variety of output voltages (40V, 50V, 80V, 160V) and current combinations (7.5A~90A), and the rated output power includes 180W, 360W, 720W, and 1080W. The single-channel model can support up to 2 units in series and 3 units in parallel, and the dual-channel and three-channel models can also support series-parallel connection between channels.


Constant Output Power
In constant output power mode, the voltage and current range is switched automatically to maximize the voltage and current without sacrificing the supply’s output power. This mode enables the supply to provide a higher output voltage at lower current and a higher output current at lower voltage. Compared to the traditional rectangular output range of most supplies, the SPS5000X series power supply provides a wider voltage and current output range, which greatly increases the utilization of the power supply.


LIST timing output
The SPS5000X series supports up to three channels and up to 50-step timing output. The user can set the timing output parameters on the front panel of the machine, or use the remote web control function for faster and more convenient settings. Under the LIST function, you can set the output current, voltage, output delay time, duration, rise and fall slope and other parameters.


CV/CC Priority Mode
When the SPS5000X series power supply is set to CC priority mode, at the power output-on stage, it is able to operate under CC priority to limit the inrush current spike and overshoot voltage effectively when the power output is turned on.

In CV priority mode, the output voltage reaches the set voltage value quickly. In some applications, such as LED testing, when the power output is started, the surge current and overshoot voltage will appear when the voltage reaches the on-state voltage of the LEDs.


Multiple Policy Protection Patterns
The protection functions of the power supply include over current protection (OCP), over voltage protection (OVP) and over temperature protection (OTP).

If protection occurs, the power supply will turn off the output and enter protection mode. Protection can be released by pressing the Esc key for at least 2 seconds.

Upon entering the Limited power protection (LPP), the system will start the power limitation mode, the maximum output power is about 105% of the rated power.
 

---

Product parameter

Max single output current 7.5 A, 10 A, 15 A, 22.5 A, 30 A, 45 A, 90 A	Max single output voltage 40 V, 50 V, 80 V, 160 V
Max output power 180 W, 360 W, 720 W, 1080 W	Channels 1, 2, 3
Display	Resolution 1 mV/1 mA
Setting accuracy	Readback accuracy
C.V Mode Line Regulation 40 V model 18 mV 50 V model 3 mV 80 V model 40 mV 160 V model 80 mV (Constant load, 90 ~ 132Vac or 170 ~ 265Vac)	C.V Mode Load Regulation 40 V model 20 mV 50 V model 10 mV 80 V model 40 mV 160 V model 80 mV (From no load to full load, constant input voltage)
C.V Mode Ripple and Noise p-p 50 V model 45 mV 40/80/160V 360W model 60 mV 40/80/160V 720W model 80 mV 40/80/160V 1080W model 100 mV r.m.s 50 Vmodel5 mV 40/80V 360W model 7 mV 40/80V 720W model 11 mV 40/80V 1080W model 14 mV 160V 360W model 12 mV 160V 720W model 15 mV 160V 1080W model 20 mV	C.V Mode Transient response time 40/50 /80 V model 1 ms 160V model 2 ms
C.V Mode Transient response time 40/50 /80 V model 1 ms 160V model 2 ms C.C Mode Line Regulation 50 V model 8 mA 40 V model 40/75/110 mA 80 V model 18/32/45 mA 160 V model 12/19/26 mA	C.C Mode Load Regulation 50 V model 10 mA 40 V model 40/75/110 mA 80 V model 18/32/45 mA 160 V model 12/19/26 mA
C.V Mode Ripple and Noise r.m.s 50 V model 10 mA 40 V model 72/144/216 mA 80 V model 27/54/81 mA 160 V model 15/30/45 mA	Max. units in series 2
Max. units in parallel 3	CV/CC Priority Mode Support
Web remote control Support	LIST Function Support, up to 50 steps, edit locally or import from USB memory
Rack mount size 1/2，1/3，1/6

 

---

Models

Models	Max single output current	Max single output voltage	Max output power	Channels	Display	Resolution	Setting accuracy	Readback accuracy
SPS5051X	10 A	50 V	180 W	1		1 mV/1 mA
SPS5041X	30 A	40 V	360 W	1		1 mV/1 mA
SPS5043X	90 A	40 V	1080 W	1		1 mV/1 mA
SPS5044X	30 A	40 V	720 W	2		1 mV/1 mA
SPS5045X	30 A	40 V	1080 W	3		1 mV/1 mA
SPS5081X	15 A	80 V	360 W	1		1 mV/1 mA
SPS5082X	30 A	80 V	720 W	1		1 mV/1 mA
SPS5083X	45 A	80 V	1080 W	1		1 mV/1 mA
SPS5084X	15 A	80 V	720 W	2		1 mV/1 mA
SPS5085X	15 A	80 V	1080 W	3		1 mV/1 mA
SPS5161X	7.5 A	160 V	360 W	1		1 mV/1 mA
SPS5162X	15 A	160 V	720 W	1		1 mV/1 mA
SPS5163X	22.5 A	160 V	1080 W	1		1 mV/1 mA
SPS5164X	7.5 A	160 V	720 W	2		1 mV/1 mA

 

---

Configure your instrument

Standard Accessories
Universal accessories

Product	Description
USB Cable	USB-A to USB-B. Used to connect instrument to PC for communication.
Power cord	The instrument comes standard with a power cord that conforms to the national standard of the user. Additional power cords in different regions can be purchased separately.
SPS5000X quick guide	Quick guide for instrument standard

Optional Accessories
Universal accessories

Product	Description
USB-GPIB Adapter	Expand the instrument’s USB interface into a GPIB interface. Using GPIB commands allows for easier execution of various operational tasks. The USB interface adheres to the USB 2.0 specification, while the GPIB interface complies with the IEEE 488.2 standard.
SPS5000X-RMK	SPS5000X series switching power supply special rack mounting kit.
30 A Test Lead	30 A test Lead
30 A Test Lead	30 A test Lead